Skip to content

Audio testing

Test tone generator

Standard audio test tones on demand — calibrate, trace, and troubleshoot without downloads.

Stopped
00:00

Stopped

Frequency

A4 · 0 cents

Tone visualizer
440 Hz · 2.27 ms per cycle

Quick tones

Waveform

Pure tone, single harmonic.

Stereo balance

Balance position: Center

−24 dBFS
Safe volume limit
Caps output at −12 dBFS

Note

Octave

Auto-stop timer

Start with low volume.
High frequencies can feel louder than they sound.

Space play/stop · ←/→ ±1 Hz (Shift ±10, Alt ±0.1) · ↑/↓ semitone · W waveform

Standard test tones and what each proves

Working installers and engineers carry a small mental set of test tones. 100 Hz checks bass extension and whether a room booms, 440 Hz is the universal tuning reference, 1000 Hz is the broadcast line-up standard for levels, 4000 Hz sits at the ear-sensitivity peak where harshness shows first, and 8000 Hz probes tweeters and treble wiring. Below that, 20 or 40 Hz separates real subwoofers from marketing.

The tool above plays any of these the moment you press play — type the hertz, drag the slider, or click a quick chip. Every tone is a pure sine by default, which is what level meters and most rules of thumb assume; switch waveforms only when you deliberately want harmonic texture in the test.

Quick test-tone cheat sheet.
ToneWhat it checksWatch for
20–40 HzSubwoofer reach, room modesSilence means the driver rolls off, not that you failed
60 HzMains-hum matching, ground loopsBuzz that matches this tone points at power wiring
100 HzBass weight, low-pass crossoversCorner swelling marks a room mode
1000 HzLevel calibration, channel trackingThe channel that reads different has the fault
4000 HzPresence, harshness, alert rangeLower the level first — this band sounds loudest
8000 HzTweeter response, codec smearRoughness signals distortion, not tone

A speaker check you can run in five minutes

Set a modest volume that will not move you to complaint level, then climb: 40, 100, 440, 1000, 4000, 8000 Hz. Note where each tone appears, which side sounds different, and where anything rattles or vanishes. Symmetry matters more than absolute answers — play each tone panned fully left, then fully right; any lasting left-right difference localizes a problem to wiring, a driver, or a room boundary.

When a tone stands out as wrong, narrow it: sweep slowly across the neighborhood to find the exact point where the problem starts and stops, then step up a decade and repeat. A rattle that lives only at 120 Hz usually means a loose grille or cabinet panel rather than a broken driver — mechanical faults are narrow, electrical ones are wide. The frequency sweep generator page automates that sweep hunt.

Beyond speakers: hum, wiring, and hearing checks

The same tones do double duty. A persistent buzz with nothing playing can be matched against the 60 Hz tone — a match points at mains interference or a ground loop, and unplugging inputs one at a time finds the guilty cable. Camera operators and field recordists use quiet tones to line up mixer and camera levels before a shoot, which prevents the classic too-quiet-then-clipped dialogue problem.

Audio hobbyists also use gentle tones as a casual hearing sketch across the range: 250, 500, 1000, 2000, 4000, 8000 Hz covers speech-critical territory. Keep the volume fixed while you climb, treat the result as curiosity rather than diagnosis, and see the dedicated hearing range test guide for the full ladder and its honest limitations.

Test tones beyond speakers: studios, cameras, and consoles

The same handful of tones runs studio and production hardware. Before a recording session, play 1000 Hz through every mixer input and watch the meters agree; any channel that reads hot or cold carries its own trim problem, not the tone’s. On video shoots, film people often line up camera and recorder levels with a short tone so both devices record the same reference — the cheap insurance that prevents the too-quiet-then-clipped dialogue problem in the edit.

Installers add a second use: identifying wiring. A tone played through a cable pair lets you match ends at the other building, label the runs, and confirm continuity of the signal path before furniture goes back. Even a simple desktop setup benefits once a year — a five-minute climb up the tone ladder catches the slowly failing speaker, the partially unseated plug, or the room that has quietly changed since repainting.

No downloads needed: tones straight from the browser

Old-school tone CD players, .mp3 test files, and paywalled apps all replaced the same idea: synthesize the tone fresh. Doing it in the browser means the tone always matches the exact hertz you type, there is no compression cooking the harmonics, and nothing to install or sign. Press play above and the oscillator starts instantly; the WAV download handles the cases where you do want a local file for a project drive or an offline bench setup.

Frequently asked questions

What is a test tone used for?

A test tone is a repeatable, known sound for checking hardware: confirming speakers reach their claimed range, matching levels between devices, locating hum and ground loops, tracing wiring pairs, and calibrating console meters. Because the tone is exactly defined, any difference between expectation and result describes the equipment rather than the signal.

Which test tone should I use for speakers?

Use a climb: 100 Hz for bass, 1000 Hz for the midrange and level, 8000 Hz for treble. Note symmetrical left-right behavior at each step and pan hard left and right to compare channels. For subwoofers add 40 Hz, and add 15 kHz when checking tweeters on full-range speakers.

Why is 1000 Hz the standard test tone?

1000 Hz sits where human hearing is sensitive, nearly every playback device reproduces it cleanly, and its character is unmistakable against program material. Decades of broadcast, studio, and manufacturing practice standardized equipment specs and procedures around it, so meters and manuals worldwide speak the same language.

Can a test tone damage my speakers or ears?

Presented sensibly, no: modest levels, short sessions, and unplugged results cause no harm. Risk concentrates at the extremes — long, loud bass stresses small drivers and echoing sustained highs annoy ears, so cap levels, use the safe limit, and stop when anything feels uncomfortable to either the equipment or you.

Do test tones need to be sine waves?

Almost always, yes: level conventions, meter ballistics, and crossover talk assume pure tones. A square or sawtooth test adds harmonic content that muddies conclusions, so keep the sine default and switch waveforms only when you are deliberately testing how a system handles harmonic-rich material.

Is this test tone generator free?

Yes — every tone on this page is free, with no account, no watermark, and no per-use limit. The tool runs entirely inside your browser using the Web Audio API, so tones are synthesized on your device rather than streamed, and the WAV download is produced locally at no cost.