20 Hz
Stopped
Low-end lab
Pure bass tones from 20 to 100 Hz — feel where your system starts, swells, and gives up.
Bass is the hardest part of any audio system to judge with music, because tracks keep moving: one moment a kick, the next a synth pad, and your attention rides the melody instead of the low end. A steady bass tone removes all of that. Press play on a single frequency below and the low end either arrives, swells, drones, or does not — a clean experiment where the system is the only variable.
Pure sine waves matter here especially. Slower waveforms add energetic harmonics that small drivers turn into midrange grumble and big amps turn into distortion, masking exactly the behavior you are judging. Keep the tone selector on sine, keep the level modest, and let the long wavelengths do the talking — in small rooms a handful of hertz separates boom from nothing, which is the point of the ladder below.
The players below climb from the floor of hearing to the edge of solidity. At 20 Hz, honest subwoofers move real pressure that you feel in your chest while ordinary speakers go silent — silence there describes driver size, not a defect. At 40 Hz and 60 Hz, home subwoofers should thump clearly and centers convert it to felt weight; the 60 Hz stop doubles as the North American mains-hum reference for hum hunting.
By 100 Hz the tone turns from pressure into a musical pitch your ear fully catches, and at 220 Hz bass has become ordinary melody. Walk the ladder after pausing at each rung: note where sound first appears (your extension floor), where one corner of the room swells (a room mode worth damping or repositioning), and where small satellites hand the baton back to the sub or give up entirely.
Long bass wavelengths bounce between walls and pile up at specific room dimensions, so almost every small room has one or two frequencies that boom while neighbors sound thin. Find yours by walking slowly while a rung plays: the corner or spot where one rung swells dramatically is a standing-wave peak, and the halfway point across the room will often sound strangely quiet for the same tone.
Treatments are physical before they are electronic: move the sub away from the wall corner, sit nearer the middle third of the room, add a rug, bookshelf, or heavy curtain at reflective boundaries, and only then consider a bass EQ trim. The walk-and-note method also transfers into mixing: if your room booms at 47 Hz, mixes made there almost always lose that exact band when played elsewhere.
Bass testing is also room testing, so repeat the ladder after rearranging furniture or moving a sub: modes shift with layout, and a rung that boomed last season can vanish after a move of two feet. Note your neighbors’ reality too — deep tones travel through walls with almost no loss, so schedule the loud experiments in daytime hours and keep the sustained runs polite.
Small speakers deserve one extra rung of honesty: if nothing at all sounds below 100 Hz, the satellites have rolled off and the sub is doing the work. That is a finding, not a failure — it tells you exactly which crossover frequencies matter and which rungs to re-test at lower volume once the sub setup is confirmed.
You may feel some of these more than hear them — keep the volume modest and walk the room while each plays.
20 Hz
Stopped
25 Hz
Stopped
30 Hz
Stopped
40 Hz
Stopped
50 Hz
Stopped
60 Hz
Stopped
Bass gains body and definite pitch through this stretch — compare where the tone stops being pressure and starts being a note.
70 Hz
Stopped
80 Hz
Stopped
100 Hz
Stopped
120 Hz
Stopped
160 Hz
Stopped
220 Hz
Stopped
Bass test tones are slow, deep pure tones in the 20 to 100 Hz range used to check how low a system actually reaches and how the room behaves. Played one at a time, they reveal subwoofer extension, room modes, rattles, and crossover handoff far more clearly than music, because nothing else is happening to distract from the low end.
Use a walk rather than one number: start at 40 Hz, confirm firm output, descend to 30 and 20 Hz to find where honest output ends, and finish at 100 Hz to hear the crossover handoff. The rung where each transition happens describes your sub better than its specification sticker.
No — music mostly masks exact behavior. A steady sine tone at one low frequency lets you hear and feel a single response point, walk the room to locate modes, and notice rattles that a busy track would cover up. Keep the tone pure: harmonics from other waveforms muddy the low-end conclusion.
At low frequencies, room boundaries act like amplifiers: waves reflect off walls and reinforce each other where they meet, building standing waves whose peaks sound enormously loud and whose nulls nearly cancel the same tone. Walk the room while a rung plays and the loud and quiet zones map your room modes directly.
High levels of long, sustained bass can overstress drivers, ports, and small enclosures, so keep volumes modest and stop if you hear rattling, port chuffing, or distortion. Brief, polite-level runs are harmless to adequate equipment; the danger lives in sustained maximum-level sweeps on undersized drivers.
Below roughly 35 Hz, sound moves from ear to body: the wavelength is longer than most rooms, and perception shifts from pitch to pressure — a chest-thumping you sense more than hear. That is normal human biology, and the same rung that feels like a breeze through your body may register as total silence to your ears.